SECTION I
TM 5-3805-255-34P
f.
QTY (Column (6)). The QTY (quantity pr figure
column) indicates the quantity of the Item used in the
breakout shown on the illustration/figure, which is
prepared for a functional group, sub-functional group, or
an assembly. A "V" appearing in this column in lieu of a
quantity indicates that the quantity is variable and the
quantity may vary from application to application.
4. Explanation of Columns (Section IV).
a.
NATIONAL STOCK NUMBER (NSN) INDEX.
(1) STOCKNUMBER column. This column lists the
NSN by National Item Identification Number (NIIN)
sequence. The NIIN consists of the last nine
NSN
digits of the NSN (i.., 5305-01-674-1467). When
NIIN
using this column to locate an Item, ignore the first
4 digits of the NSN. However, the complete NSN should
b used when ordering items by stock number.
(2)
FIG. column. This column lists the number of
the figure where the Item is identified/located. The
figures are in numerical order in Section II and Section
Ill.
(3)
ITEM column. The Item number identifies the
Item associated with the figure listed in the adjacent FIG.
column. This Item is also identified by the NSN listed on
the same line.
b.
PARETNUMBER INDEX. Part numbers in this
index
are
listed
by
part
number
in
ascending
alphanumeric sequence (i.., vertical arraignment of letter
and number combination which places the first letter or
digit of each group in order A through Z, followed by the
numbers 0 through 9 and each following letter or digit in
like order).
(1)
CAGEC column. The Commercial and Gov.-
remnant Entity (CAGE) Cod (C) is a 5-digit alphanumeric
cod used to identify the manufacturer, distributor, or
Government agency, etc., that supplies the Item.
(2)
PARET NUMBER column. Indicates the primary
number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the
design and characteristics of the Item by mans of its
engineering drawings, specifications standards, and
inspection requirements to identify an Item or rang of
items.
(3)
STOCK NUMBER column. This column lists the
NSN for the associated part number and manufacturer
identified in the PARET NUMBER and FSCM/CAGE
columns to the left.
(4)
FIG.
column. This column lists the number of
the figure where the Item is identified/located in Sections
II and III.
(5)
ITEM column. The Item number is that number
assigned to the Item as it appears in the figure
referenced in the adjacent figure number column.
c
FIGURE AND ITEM NUMBER INDEX.
(1)
FIG. .column. This column lists the number of
the figure where the Item is identified/located in Sections
II and III.
(2)
ITEM column. The Item number is that number
assigned to the Item as it appears in the figure
referenced in the adjacent figure number column.
(3)
STOCK NUMBER column. This column lists the
NSN for the Item.
(4)
CAGEC column. The Commercial and
Government Entity (CAGE) Cod (C) is a 5-digit alpha-
numeric
cod
used
to
identify
the
manufacturer,
distributor, or Government agency, etc., that supplies the
Item.
(5)
PARET NUMBER column. Indicates the primary
number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the
design and characteristics of the Item by mans of its
engineering drawings, specifications standards and
inspection requirements to identify an Item or rang of
items.
5. Special Information.
a
USABLE ON CODE. The usable on cod appears
in the lower left comer of the Description column
heading. Usable on cods are shown as "UOC: in the
Description column (justified left) on the first line
following
applicable
Item
description/nomenclature.
Uncoded items are applicable to all models. Identification
of the usable on cods used in the RPSTL are:
Cod
Used On
U93
Model H100C GPB
U94
Model H100C RB
b
FABRICATION INSTRUCTIONS. Bulk materials
required to manufacture items are listed in the Bulk
Martial Functional Group of these RPSTL. Part numbers
for bulk materials are also referenced in the Description
column of the line Item entry for the Item to b
manufactured/fabricated. Detailed fabrication instructions
for items source coded to b manufactured or fabricated
are found in TM 5-3805-255-14&R
c.
ASSEMBLY
INSTRUCTIONS.
Detailed
assembly instructions for items source coded to b
assembled from component spare/Repair parts are
found in TM
Change 1 4
