TM 5-3805-262-20CLEANING(a) Clean hose (4) using clean cloth moistened with detergent. Dry usingc l e a n c l o t h s .Dry cleaning solvent P-D-680 used to clean parts is toxic and flammable.W e a r p r o t e c t i v e g o g g l e s a n d g l o v e s a n d u s e o n l y i n a w e l l v e n t i l a t eda r e a . A v o i d c o n t a c t w i t h s k i n ,e y e s a n d c l o t h e s a n d d o n ’ t b r e a t h ev a p o r s .Do not use near open flame or excessive heat and don’t smokew h e n u s i n g i t .Failure to do so could cause serious injury. If you be-c o m e d i z z y w h i l e u s i n g c l e a n i n g s o l v e n t , g e t f r e s h a i r a n d m e d i c ala t t e n t i o n i m m e d i a t e l y .If contact with skin or clothes is made, flushwith large amounts of water.I f c o n t a c t w i t h e y e s i s m a d e , w a s h e y eswith water and get medical aid immediately.(b) Clean remaining parts using cleaning solvent P-D-680. Dry using cleanc l o t h s .Compressed air used for cleaning purposes will not exceed 30 psi. Useo n l y w i t h e f f e c t i v e c h i p g u a r d i n g a n d p e r s o n a l p r o t e c t i v e e q u i p m e n t( g o g g l e s / s h i e l d , g l o v e s , e t c ) . F a i l u r e t o d o s o c o u l d c a u s e s e r i o u si n j u r y t o e y e s a n d p o s s i b l e b l i n d n e s s.If you hurt your eyes or if af o r e i g n o b j e c t i s b l o w n i n t o y o u r e y e s ,s e e k m e d i c a l a t t e n t i o nimmediately.(c) Use compressed air to clear foreign matter from hose (4), adapters (2,5, 9, and 22), fittings (7 and 20), and tubes (12, 25, and 26).lNSPECTION(a) Inspect hose (4) for cracks or deterioration. Replace as necessary.(b) Inspect tubes (12, 25, and 26) for cracks, breaks, dents, and deforma-t i o n . C h e c k t u b e f i t t i n g s ( 6, 11, 19, and 24) for cracks, damagedthreads, or deformation. If tube fittings are damaged, replace tube.(c) Inspect fittings (7 and 20) and adapters (2, 5, 9, and 22) for cracks,breaks, or other damage. Replace as necessary.( d ) I n s p e c t r e m a i n i n g p a r t s f o r c r a c k s , b r e a k s , d e f o r m a t i o n , d i s t o r t i o n , a nddamaged threads. Replace as necessary.INSTALLATION (SHEET 1 OF 2)(a) If removed, put bracket (33) on axle housing stud and secure using wash-er (32) and nut (31). Tighten nut securely.(b) Position tee (30) on bracket (33). Install capscrew (29), lock washer(28), and nut (27). Tighten nut securely.(c) Put new gasket (21), adapter (22), and new O-ring (23) on fitting (20).7-39
Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business