TM 5-3805-262-20
REMOVAL (SHEET 5 OF 5)
(y) Loosen two clamps (34) and disconnect hose (35) from
( 3 7 ) .
(z) Remove two clamps (34) from hose
loader, remove hardware securing
and clamp (36) from hose.
(aa) If necessary, remove elbow (37);
(ab) Loosen hose fittings at each end
e r .
(35). If hose is to
manifold and elbow
be removed from
clamp (36) then remove hose from loader
remove and discard 0-ring (38).
of tube (39) and remove tube from load-
(ac) If necessary, remove elbows (40 and 42). Discard 0-ring (41).
CLEANING
(a) Clean hoses (1, 3, 4, 5, 6, 13, 17, and 35) using clean cloth moistened
with detergent. Dry using clean cloth.
Dry cleaning solvent P-D-680 used to clean parts is toxic and flammable.
W e a r p r o t e c t i v e g o g g l e s a n d g l o v e s a n d u s e o n l y i n a w e l l v e n t i l a t ed
a r e a . A v o i d c o n t a c t w i t h s k i n , e y e s a n d c l o t h e s a n d d o n ’ t b r e a t he
vapors. Do not use near open flame or excessive heat and don’t smoke
w h e n u s i n g i t. F a i l u r e t o d o s o c o u l d c a u s e s e r i o u s i n j u r y . I f y o u
b e c o m e d i z z y w h i l e u s i n g c l e a n i n g s o l v e n t , g e t f r e s h a i r a n d m e d i c al
a t t e n t i o n i m m e d i a t e l y . I f c o n t a c t w i t h s k i n o r c l o t h e s i s m a d e , f l u sh
w i t h l a r g e a m o u n t s o f w a t e r .
If contact with eyes is made, wash eyes
with water and get medical aid immediately.
Compressed air used for cleaning purposes will not exceed 30 psi. Use
o n l y w i t h e f f e c t i v e c h i p g u a r d i n g a n d p e r s o n a l p r o t e c t i v e e q u i p m e nt
( g o g g l e s / s h i e l d , g l o v e s ,
e t c ) . F a i l u r e t o d o s o c o u l d c a u s e s e r i o us
i n j u r y t o e y e s a n d p o s s i b l e b l i n d n e s s.
I f y o u h u r t y o u r e y e s o r i f a
f o r e i g n o b j e c t i s b l o w n i n t o y o u r e y e s , s e e k m e d i c a l a t t e n t i o n
immediately.
(b) Clean remaining parts by immersing in cleaning solvent P-D-680; dry
using compressed air. Flush interior of fittings and elbows using com-
p r e s s e d a i r .
(c) Flush interior of hoses (1, 3, 4, 5, 6, 13, 17, and 35) and tubes (7 and
39) using clean hydraulic oil. Use compressed air to clear any obstruc-
tions from inside hoses and tubes.
8-21
