TM 5-3805-262-20
CLEANING AND INSPECTION
Dry cleaning solvent P-D-680 used to clean parts is toxic and flammable.
W e a r p r o t e c t i v e g o g g l e s a n d g l o v e s a n d u s e o n l y i n a
a r e a . A v o i d c o n t a c t w i t h s k i n , e y e s a n d c l o t h e s a n d
vapors .
D o n o t u s e n e a r o p e n f l a m e o r e x c e s s i v e h e at
w h e n u s i n g i t . F a i l u r e t o d o s o c o u l d c a u s e s e r i o us
b e c o m e d i z z y w h i l e u s i n g c l e a n i n g s o l v e n t , g e t f r e sh
a t t e n t i o n i m m e d i a t e l y . I f c o n t a c t w i t h s k i n o r c l o t h e s
w i t h l a r g e a m o u n t s o f w a t e r . I f c o n t a c t w i t h e y e s i s
with water and get medical aid immediately.
(1) Clean all parts using cleaning solvent P-D-680; dry
w e l l v e n t i l a t ed
d o n ’ t b r e a t h e
and don’t smoke
i n j u r y . I f y o u
air and medical
i s m a d e , f l u sh
made, wash eyes
using clean cloths.
(2) Check hood support (5) and bracket (9) for cracks, breaks, dents, or ex-
cessive corrosion. Remove corrosion using a stiff wire brush. Touch up
all bare metal areas using MIL-C-46168 paint, color forest green.
( 3 ) I n s p e c t r e m a i n i n g p a r t s f o r c r a c k s,
b r e a k s , d i s t o r t i o n , d e f o r m a t i o n , a nd
damaged threads. Replace as necessary.
INSTALLATION
(1) If necessary, position bracket (9) on hood support (5) and secure using
two capscrews (8), lock washers (7), and nuts (6).
When using chain hoist to remove or install parts, be sure chain hoist
i s s e c u r e l y f a s t e n e d t o t h e p a r t a n d t h a t a l l s l a c k i n c h a i n i s t a k e n
up. Failure to do so could cause serious injury due to the part falling
o n y o u. I f y o u a r e i n j u r e d b y f a l l i n g e q u i p m e n t , o b t a i n m e d i c a l a i d
immediately.
(2)
(3)
( 4)
( 5)
(6)
(7)
(8)
( 9)
Using chain hoist, position hood support (5) on front of rear chassis.
Secure hood support (5) using four washers (4), capscrews (3), lock wash-
ers (2), and nuts (1), Tighten nuts and capscrews securely.
Disconnect chain hoist from hood support (5).
I n s t a l l t r a n s p o r t / s e r v i c e l i n k ( p a g e 9 - 9 ) .
I n s t a l l r e s t r i c t i o n i n d i c a t o r ( p a g e 4 - 3 0 ).
Install hourmeter/tachometer (page 5-67).
I n s t a l l h y d r a u l i c o i l c o o l e r ( p a g e 8 - 3 7 ) .
Install engine hoods (page 9-20).
9-23
