TM 5-3805-262-20
REMOVAL (SHEET 2 OF 2)
( 5 ) R e p e a t s t e p s ( 3 ) a n d ( 4)
c e s s a r y.
( 6 ) R e p e a t s t e p s ( 1 ) t h r o u gh
n e c e s s a r y.
above to remove remaining bracket(s) (12) as ne-
(5) above to remove remaining front fender as
CLEANING AND INSPECTION
Dry cleaning solvent P-D-680 used to clean parts is toxic and flammable.
W e a r p r o t e c t i v e g o g g l e s a n d g l o v e s a n d u s e o n l y i n a w e l l v e n t i l a t ed
a r e a . A v o i d c o n t a c t w i t h s k i n,
e y e s a n d c l o t h e s a n d d o n ’ t b r e a t h e
v a p o r s .
Do not use near open flame or excessive heat and don’t smoke
w h e n u s i n g i t . F a i l u r e t o d o s o c o u l d c a u s e s e r i o u s i n j u r y . I f Y O U
b e c o m e d i z z y w h i l e u s i n g c l e a n i n g s o l v e n t , g e t f r e s h a i r a n d m e d i c al
a t t e n t i o n i m m e d i a t e l y . I f c o n t a c t w i t h s k i n o r c l o t h e s i s m a d e , f l u sh
w i t h l a r g e a m o u n t s o f w a t e r.
If contact with eyes is made, wash eyes
with water and get medical aid immediately.
(1) Clean all parts using cleaning solvent P-D-680; dry using clean cloths.
( 2 ) C h e c k f r o n t f e n d e r s ( 6 ) a n d b r a c k e t s ( 1 2 ) f o r c r a c k s , b r e a k s , d e n t s , or
e x c e s s i v e c o r r o s i o n . R e m o v e c o r r o s i o n u s i n g a s t i f f w i r e b r u s h . T o u c h up
all bare metal areas using MIL-C-46168 paint, color forest green .
( 3 ) I n s p e c t r e m a i n i n g p a r t s f o r c r a c k s , b r e a k s , d i s t o r t i o n , d e f o r m a t i o n , a nd
damaged threads. Replace as necessary.
INSTALLATION
(1)
(2)
(3)
( 4 )
(5)
(6)
(7)
Position and support bracket (12) on front chassis and install two
washers (11) and capscrews (10).
Hold capscrews (10) using socket wrench while an assistant installs and
tightens two washers (9), lock washers (8), and nuts (7). Tighten nuts
and capscrews securely.
Repeat steps (1) and (2) above for remaining bracket(s) (12) as
n e c e s s a r y.
Position and support front fender (6) on brackets (12).
Install six washers (5), capscrews (4), washers (3), lock washers (2),
and nuts (1) to secure front fender (6). Tighten nuts and capscrews
s e c u r e l y.
Repeat steps (1) through (5) above to install remaining front fender (6).
R e i n s t a l l b l a c k o u t d r i v i n g l i g h t ( p a g e 5 - 1 0 1 ) o n l e f t f r o n t f e n d e r .
9-25
