TM 5-3805-291-10
Systems Operation Section
Inverted Image
1. Press button 4 (Contrast) and button 5
(Brightness) simultaneously in order to access
this option.
This option can be used in order to invert the image.
That is, this option will switch the orientation of the
2. Press button 6 (Minus) or button 7 (Plus) button
image so that the top will appear at the bottom of
in order to change the level of color.
the display screen and the bottom will appear at
the top of the display screen. Therefore, the image
will appear to be upside down if the inverted image
Press any other display button, other than the button
6 (Minus) or button 7 (Plus) buttons, in order to exit
option is selected.
the Color Adjustment option.
In order to invert the image:
Marker ON/OFF
1. Press button 1 (camera select) in order to enter
"Manual" mode. The LED that is above and to the
Note: Before the marker option is enabled,
right of button 1 (camera select) will flash in order
the appropriate "on-sight" personel should be
to indicate that the system is in manual mode.
contacted. The technician will need information
in order to accurately set the marker at the
2. Press and hold button 1 (camera select) and
desired position.
button 2 (Auto Brightness) simultaneously for 40
seconds in order to invert the image of the camera
The display provides an option that is called the
view that is shown on the display screen.
"Marker" line. The "Marker" is a small green line that
provides a fixed distance reference line from the
3. Press button 1 (camera select) again in order to
machine. This Marker line can be turned on or off.
select the next camera that is to be viewed and/or
The position of the Marker line can also be set by a
have its settings adjusted.
qualified technician.
4. Again, press and hold button 1 (camera select)
In order to turn the Marker on:
and button 2 (Auto Brightness) simultaneously
for 40 seconds in order to invert the image of the
1. Press button 2 (Auto Brightness) and button 3
camera view that is shown on the display screen.
(Standby) simultaneously for 10 seconds. The
marker will appear on the display screen.
5. Repeat step 3 and step 4 for the third camera.
2. After the "Marker" appears, press either button 6
In order to revert to a previous image:
(Minus) or button 7 (Plus) in order to adjust the
position of the "Marker".
1. Follow the preceding steps to select the
appropriate camera.
3. Once the position is set, press any other display
button except button 6 (Minus) or button 7 (Plus)
2. Press and hold button 1 (camera select) and
in order to exit the "Marker" set option.
button 2 (Auto Brightness) simultaneously for 40
seconds.
Note: After the marker has been activated, if any
other button on the display is pressed other than
Display Power ON/OFF
button 6 (Minus) or button 7 (Plus), the marker will be
set to the current position on the display. The marker
position can be changed as long as the marker option
The display on/off button may be disabled. If disabled,
has not been exited.
the button serves no other function. The LED that is
above and to the right of the display on/off button will
In order to access all other options, please
illuminate in order to show the system is on.
refer to the following information in the "Single
Camera System" or the "Multi Camera System"
Color Adjustment
sections of this document.
The "Color Adjustment" option is used to vary the
Reset Marker
level of color on the display. The level of color of the
display can be varied in order to show a full color
In order to reset the marker, the marker must be
image or a black and white image.
turned off, then turned back on and moved to the
desired position on the display screen using button
In order to access the color adjustment option:
6 (Minus) or button 7 (Plus), before any other button
on the display is pressed.
In order to reset the marker:
0004 00-71
